EN
Search

BECA 810

BECA 810
BECA 810
beca_810_3d_image_v3
beca_810_3d_image_v4

Description

The BECA 810 profile is a standard stainless steel sleeve.

Advantages

Good corrosion resistance
Good chemical inertia
Extremely thin, no need to modify the dimensions of the shaft seal
Easy to fit

Technical data

Applications

Hubs
Pinions
Differentials
Gear boxes
Crankshafts

Materials

Material

Stainless steel - AISI 304

Hardness

More than 220 HV (95 HRB)

Thickness

0.28 mm (0/-0.05)

Surface roughness

Ra = 0.20 - 0.50 µm

Dimensions
Assembly recommendations

Dimensions

Installation drawingInstallation Manchon d'usure - Installation Sleeve - BECA 810

Assembly recommendations

Please refer to the instructions below to correctly fit the sleeves:

  • Clean the soiled areas of the shaft at the point of contact with the sealing lip of the ring. File down all burrs or rough areas to ensure that the sleeve does not prematurely deteriorate when fitted in a groove or any other part.
  • Using a calliper, measure the diameter of the shaft in 3 different positions and check that the average over these 3 measurements indicates a value that complies with the recommended dimensional range. If that is the case, the sleeve will have a sufficiently tight fit on the shaft to prevent any possible sliding.
  • Determine and mark where the sleeve must be positioned to cover the worn area, up to the end of the shaft.
  • The shallow wear grooves do not need to be filled. It is, however, possible to apply a sealing product to the inside diameter of the sleeve. Clean off any surplus product.
  • Deeper grooves can be filled with a metal-epoxy powder. Install the sleeve before the product hardens. Remove the surplus product.
  • When mounting the sleeve, the mechanical body must be shut down.
  • If the collar must be removed after installation, cut before installing part of the thinnest area using the outside diameter of the sleeve.
  • Position the sleeve in the mounting tool; it must be inserted into the shaft in its entirety. Use a mallet to tap on its centre, until the sleeve covers the worn shaft. Ensure that the mounting tool is dimensionally compatible, so as to insert the sleeve without distorting it.
  • Ensure that the outside of the sleeve has not been damaged during fitting. Its surface roughness and its cleanliness are two elements that determine the correct operation of the seal.
  • The length of the sleeve must not exceed the full length of the shaft, excluding the chamfer.

Mounting recommendations for the sleeves

266 dimensions found
810.1039901
Standard request
103,89 104,09 103,99 112,73 19,99 24,00 35,99
810.1047802
Standard request
104,70 104,90 104,78 113,54 20,65 25,40 34,93
810.1050001
Standard request
104,90 105,11 105,00 113,54 19,99 23,19 35,00
810.1063802
Standard request
106,25 106,45 106,38 114,30 20,65 25,40 34,93
810.1075401
Standard request
107,34 107,54 107,54 117,09 19,84 23,01 36,53
810.1079502
Standard request
107,90 108,10 107,95 117,09 20,65 25,40 36,53
810.1099301
Standard request
109,91 110,11 109,93 124,99 12,93 16,51 31,75
810.1100101
Standard request
109,78 110,01 110,01 124,99 11,38 14,96 32,94
810.1111302
Standard request
111,00 111,20 111,13 120,65 20,65 25,40 41,91
810.1119901
Standard request
111,79 111,99 111,99 120,65 19,05 22,50 33,02
810.1127302
Standard request
112,62 112,83 112,73 122,25 25,40 29,01 33,35
810.1143002
Standard request
114,20 114,40 114,30 123,19 20,65 25,40 31,75
810.1150102
Standard request
114,88 115,09 115,01 127,00 20,65 23,83 31,75
810.1174801
Standard request
117,37 117,58 117,48 127,00 11,13 15,88 34,93
810.1174802
Standard request
117,37 117,58 117,48 128,60 25,40 31,75 34,93
810.1190802
Standard request
119,00 119,20 119,08 128,60 20,65 25,40 34,93
810.1199908
Standard request
119,89 120,09 119,99 129,79 8,00 11,00 33,60
810.1199901
Standard request
119,89 120,09 119,99 129,79 19,99 24,99 32,00
810.1206501
Standard request
120,55 120,75 120,65 127,00 12,70 19,05 38,10
810.1220001
Standard request
121,89 122,10 122,00 131,50 19,99 24,00 32,00
810.1230101
Standard request
122,91 123,11 123,01 132,82 19,99 24,99 31,60
810.1238301
Standard request
123,72 123,93 123,83 133,35 15,88 19,05 36,53
810.1249901
Standard request
124,89 125,10 124,99 137,16 10,01 14,00 36,53
810.1249902
Standard request
124,89 125,10 124,99 137,16 26,01 32,00 36,53
810.1270002
Standard request
124,89 125,10 127,00 136,91 20,65 25,40 36,53
810.1270001
Standard request
126,95 127,15 127,00 137,16 13,72 17,30 36,53
810.1280002
Standard request
127,80 128,00 128,00 135,26 29,21 34,27 40,30
810.1299001
Standard request
129,79 130,00 129,90 139,52 19,05 23,83 30,00
810.1300002
Standard request
129,97 130,18 130,00 139,52 22,00 25,30 32,51
810.1301802
Standard request
130,05 130,25 130,18 139,70 20,65 25,40 31,75
810.1333502
Standard request
133,25 133,45 133,35 141,22 20,65 25,40 31,75
810.1349002
Standard request
134,80 135,00 134,90 145,67 20,50 25,40 31,75
810.1365302
Standard request
136,42 136,63 136,53 149,23 20,65 25,40 31,75
810.1381303
Standard request
138,02 138,23 138,13 146,05 38,10 42,88 47,63
810.1390901
Standard request
138,99 139,19 139,09 149,86 14,30 19,05 31,34
810.1397001
Standard request
139,65 139,85 139,70 150,83 13,16 17,91 31,75
810.1397002
Standard request
139,65 139,85 139,70 150,83 20,65 25,40 31,75
810.1400002
Standard request
139,90 140,11 140,00 151,00 20,50 25,40 31,75
810.1428802
Standard request
142,77 142,98 142,88 157,18 22,23 25,40 46,02
810.1450101
Standard request
144,75 145,01 145,01 154,94 19,05 22,23 46,02
810.1456401
Standard request
145,44 145,64 145,64 154,94 14,30 19,05 49,23
810.1460502
Standard request
145,95 146,15 146,05 156,97 20,65 25,40 44,45
810.1492302
Standard request
149,12 149,33 149,23 157,18 25,40 31,75 33,35
810.1499902
Standard request
149,76 150,01 149,99 159,00 26,01 30,00 32,51
810.1508302
Standard request
150,72 150,93 150,83 161,93 25,40 28,58 47,63
810.1524001
Standard request
152,27 152,48 152,40 161,54 12,70 19,05 44,45
810.1524002
Standard request
152,27 152,48 152,40 161,93 25,40 31,75 44,45
810.1540002
Standard request
153,87 154,13 154,00 161,93 26,01 30,00 32,99
810.1548602
Standard request
154,74 154,99 154,86 167,01 26,01 30,00 32,99
810.1575602
Standard request
157,43 157,68 157,56 168,28 20,65 27,00 44,45
810.1587502
Standard request
158,62 158,88 158,75 168,28 26,19 31,75 44,45
810.1599902
Standard request
159,74 159,99 159,99 171,45 25,40 31,75 34,93
810.1651002
Standard request
164,97 165,23 165,10 177,80 25,40 31,75 34,93
810.1698803
Standard request
169,75 170,00 169,88 182,58 31,75 38,00 44,45
810.1714502
Standard request
171,32 171,58 171,45 180,98 20,65 27,00 44,45
810.1750102
Standard request
174,75 175,01 175,01 186,99 27,99 32,00 35,00
810.1778002
Standard request
177,67 177,93 177,80 189,87 25,40 31,75 42,88
810.1800103
Standard request
179,76 180,01 180,01 190,50 32,99 38,00 44,50
810.1841503
Standard request
184,00 184,25 184,15 197,10 31,75 38,10 55,25
810.1848603
Standard request
184,73 184,99 184,86 197,10 32,00 38,00 54,99
810.1893102
Standard request
189,08 189,33 189,31 199,64 20,65 25,40 31,75
810.1905002
Standard request
190,37 190,63 190,50 200,03 20,65 25,40 31,75
810.1968502
Standard request
196,72 196,98 196,85 210,06 25,40 33,35 47,63
810.2000303
Standard request
199,87 200,13 200,03 212,73 34,52 38,10 44,45
810.2016302
Standard request
201,50 201,75 201,63 212,73 25,40 31,75 44,45
810.2032002
Standard request
203,07 203,33 203,20 212,73 25,40 31,75 44,45
   1 2 3